Issue 41

S.M.J. Razavi et alii, Frattura ed Integrità Strutturale, 41 (2017) 432-439; DOI: 10.3221/IGF-ESIS.41.54 439 [4] Ayatollahi, M.R., Nemati Giv, A., Razavi, S.M.J., Khoramishad, H., The Effect of orientations of metal macrofiber reinforcements on the mechanical properties of adhesively bonded single lap joints, J. Adhes., (in press). DOI: 10.1080/00218464.2017.1305270. [5] Razavi, S.M.J., Esmaeili, E., Samari, M., Razavi, S.M.R., Stress analysis on a non-flat interface bonded joint, J. Adhes., (in press). DOI: 10.1080/00218464.2016.1257942. [6] Esmaeili, E., Razavi, S.M.J., Bayat, M., Berto, F., Flexural behavior of metallic fiber-reinforced adhesively bonded single lap joints, J. Adhes., (in press). DOI: 10.1080/00218464.2017.1285235. [7] Lokaj, A., Klajmonova, K., Comparison of behaviour of laterally loaded round and squared timber bolted joints, Frattura ed Integrita Strutturale, 11(39) (2017) 56-61. [8] Espallargas, N., Aune, R.E., Torres, C., Papageorgiou, N., Munoz, A.I., Bulk metallic glasses (BMG) for biomedical applications—A tribocorrosion investigation of Zr55Cu30Ni5Al10 in simulated body fluid, Wear, 301(1-2) (2013) 271-279. [9] Espallargas, N., Johnsen, R., Torres, C., Munoz, A.I., A new experimental technique for quantifying the galvanic coupling effects on stainless steel during tribocorrosion under equilibrium conditions, Wear, 307(1-2) (2013) 190-197. [10] Espallargas, N., Torres, C., Munoz, A.I., A metal ion release study of CoCrMo exposed to corrosion and tribocorrosion conditions in simulated body fluids, Wear, 332-333 (2015) 669-678. [11] Haugan, E.B., Næss, M., Torres Rodriguez, C., Johnsen, R., Iannuzzi, M., Effect of Tungsten on the Pitting and Crevice Corrosion Resistance of Type 25Cr Super Duplex Stainless Steels, Corrosion, 73(1) (2017) 53-67. [12] Jiang, J.H., Ma, A.B., Weng, W.F., Fu, G.H., Zhang, Y.F., Liu, G.G., Lu, F.M., Corrosion fatigue performance of pre- split steel wires for high strength bridge cables, Fatigue Fract. Eng. Mater. Struct., 32 (2009) 769–779. [13] Yang, W.J., Yang, P., Li, X.M., Feng, W.L., Influence of tensile stress on corrosion behaviour of high strength galvanized steel bridge wires in simulated acid rain, Mater. Corros., 63 (2012) 401–407. [14] Berchem, K., Hocking, M.G., The influence of pre-straining on the corrosion fatigue performance of two hot-dip galvanised steels, Corros. Sci., 48 (2006) 4094–4112. [15] Berchem, K., Hocking, M.G., The influence of pre-straining on the high-cycle fatigue performance of two hot-dip galvanised car body steels, Mater. Charact., 58 (2006) 593–602. [16] James, M.N., Designing against LMAC in galvanised steel structures, Eng. Fail. Anal., 16 (2009) 1051–1061. [17] Di Cocco, V., Sn and Ti influences on intermetallic phases damage in hot dip galvanizing, Frattura ed Integrità Strutturale, 22 (2012) 31-38. [18] Bergengren, Y., Melander, A., An experimental and theoretical study of the fatigue properties of hot dip-galvanized high strength sheet steel, Int. J. Fatigue, 14 (1992) 154–162. [19] Nilsson, T., Engberg, G., Trogen, H., Fatigue properties of hot-dip galvanized steels. Scand. J. Metall., 18 (1989) 166– 175. [20] Browne, R.S., Gregory, E.N., Harper, S., The effects of galvanizing on the fatigue strengths of steels and welded joints, In: Proc. Seminar on Galvanizing of Silicon Containing Steels, ILZRO Publishers, Liege, (1975) 246–264. [21] Vogt, J.B., Boussac, O., Foct, J., Prediction of fatigue resistance of a hot-dip galvanized steel, Fatigue Fract. Eng. Mater. Struct., 23 (2000) 33–39. [22] Valtinat, G., Huhn, H., Bolted connections with hot dip galvanized steel members with punched holes. Connections in Steel Structures V, Amsterdam, (2004) 297-309. [23] Berto, F., Mutignani, F., Tisalvi, M., Laurenti, A., Effect of hot-dip galvanization on the fatigue behavior of notched and welded structural steel, Ingegneria ferroviaria, 2 (2016) 105-118. [24] Gallo, P., Berto, F., Glinka, G Generalized approach to estimation of strains and stresses at blunt V-notches under non-localized creep, Fatigue Fract. Eng. Mater. Struct., 39 (2016) 292-306.