Issue 36

F. Z. Liu et alii, Frattura ed Integrità Strutturale, 36 (2016) 139-150; DOI: 10.3221/IGF-ESIS.36.14 140 been processed by hot forming. With the rapid development of hot forming technology, it is urgent to evaluate the delay fracture behavior of hot formed ultra high-strength steel plate. On account of this, this study processed a kind of low- carbon Mn-B ultra high-strength steel plate with conventional thermal processing and hot forming technique and studied the effects of tempering temperature and hot forming process on its hydrogen-induced delay fracture resistance, which can provide a reference for the actual application of such kind of steel plate. M ATERIALS AND METHOD Experimental material he material used in the test was the improved Mn-B cold-rolled steel plate (1500 MPa) which was self-developed. It was produced using techniques of rotating furnace, external refining, continuous casting and continuous rolling. The thickness of steel plate was 1.5 mm. Its chemical components and their mass fractions were as follows: Si (0.85), C (0.20), Mn (1.60), S (0.002), P (0.006) and B (0.0015). The experimental steel was first heated into 950 °C and then cooled with water after 20-min insulation. The hardened martensitic structure obtained was tempered at 100, 200 and 400 °C sequentially for 120 min and then cooled in the air. The process is shown in Tab. 1. No. of samples Heat treatment system 1 950 °C × 20 min, water cooling / 2 100°C×120min, air cooling 3 200°C×120min, air cooling 4 400°C×120min, air cooling Table 1 : Heat treatment system of experimental materials. Experimental method To test the tensile performance of the experimental material in quenched state at different tempering temperatures, a tensile experiment was carried out on tensile sample using material testing machine. Constant-load notch tensile experiment was used to evaluate the resistance of the experimental material. The ratio of critical fracture stress c  to notch strength N  , i.e., delay fracture strength ratio / c N   was used to evaluate the delay fracture resistance of the experimental materials. The higher the value was, the better the delay fracture resistance was. To avoid the size effect of thin plate shape samples on hydrogen absorption and dehydrogenation behaviors, the experimental steel plate with a thickness of 6.0 mm was processed into a round bar sample with a size of 5 × 40 mm. Then electrochemical hydrogen charging was performed on NaOH solution (0.1mol/L); the current density used was 4 mA/cm 2 and the process lasted for 72 h. After hydrogen charging and surface grinding, the content of hydrogen in the sample was tested using thermal desorption spectrometry (TDS); the heating temperature was 800 °C and the heating rate was 100 °C/h. Activation energy of hydrogen traps in the sample was tested by varying the heating rate of TDS. The content of hydrogen of hydrogen filled sample was measured at different time points; in this way, the diffusion coefficient of hydrogen in the experimental material was calculated. Besides, the notched tensile sample was loaded in corrosive liquid under the effect of critical stress for 100 h. The working segment near the corroded notch was cut using wire cutting. To estimate the critical hydrogen content of the experimental material, the content of hydrogen was measured using TDS as well after grinded with 1000 # abrasive paper. Constant-load delay fracture experiment, electronic hydrogen charging experiment and test with TDS were carried out on experimental materials in conventional quenching state and at different tempering temperatures to study the delay fracture resistance as well as behaviors of hydrogen absorption and effusion and discuss over the effects of quenching and tempering temperature on the delay fracture resistance of the experimental materials. R ESULTS AND DISCUSSION Mechanical performance of experimental materials ig. 1 shows the changes of tensile performance of the experimental materials along with tempering temperature. It can be seen that, the experimental material had high strength and good plasticity; tensile strength weakened after tempering at 100 °C, whereas yield strength improved. In different states, elongation fluctuated, but slightly. Only T F