Issue 35

S. Morita et alii, Frattura ed Integrità Strutturale, 35 (2016) 82-87; DOI: 10.3221/IGF-ESIS.35.10 87 [7] Li, Y., Enoki, M., Deformation and anelastic recovery of pure magnesium and AZ31B alloy investigated by AE, Mater. Trans., 48 (2007) 2343–2348. [8] Li, Y., and Enoki, M., Recovery Behaviour of Pure Magnesium in Cyclic Compression-Quick Unloading-Recovery Process at Room Temperature Investigated by AE, Mater. Trans., 49 (2008) 1800–1805. [9] Hasegawa, S., Tuchida, Y., Yano, H., Matsui, M., Evaluation of low cycle fatigue life in AZ31 magnesium alloy, Int. J. Fatigue, 26 (2007) 1839–1845. [10] Lin, X.Z., Chen, D.L., Strain controlled cyclic deformation behavior of an extruded magnesium alloy, Mater. Sci. Eng. A, 496 (2008) 106–113. [11] Matsuzuki, M., Horibe, S., Analysis of fatigue damage process in magnesium alloy AZ31, Mater. Sci. Eng. A, 504 (2009) 169–74. [12] Begum, S., Chen, D.L., Xu, S., Luo, Alan A., Effect of strain ratio and strain rate on low cycle fatigue behavior of AZ31 wrought magnesium alloy, Mater. Sci. Eng. A, 517 (2009) 334–343. [13] Lv, F., Yang, F., Duan, Q.Q., Luo, T.J., Yang, Y.S., Li, S.X., Zhang, Z.F., Tensile and low-cycle fatigue properties of Mg–2.8% Al–1.1% Zn–0.4% Mn alloy along the transverse and rolling directions, Scripta Mater., 61 (2009) 887–890. [14] Park, S.H., Hong, S.G., Bang, W., Lee, C.S., Effect of anisotropy on the low-cycle fatigue behavior of rolled AZ31 magnesium alloy, Mater. Sci. Eng. A, 527 (2010) 417–423. [15] Ando, S., Iwamoto, N., Hori, T., Tonda, H., Fatigue Crack Propagation in Magnesium Crystals, J. Japan Inst. Metals, 65 (2001) 187–190. [16] Ando, S., Saruwatari, K., Hori, T., Tonda, H., Fatigue Crack Propagation Behavior in Magnesium Single Crystals, J. Japan Inst. Metals, 67 (2003) 247–251. [17] Ando, S., Ikejiri, Y., Iida, N., Tsushida, M., Tonda, H., Orientation Dependence of Fatigue Crack Propagation in Magnesium Single Crystals, J. Japan Inst. Metals, 70 (2006) 634–637. [18] Kim, H.-K., Lee, Y.-I., Chung, C.-S., Fatigue properties of a fine-grained magnesium alloy produced by equal channel angular pressing, Scripta Mater., 52 (2005) 473–477. [19] Uematsu, Y., Tokaji, K., Kamakura, M., Uchida, K., Shibata, H., Bekku, N., Effect of extrusion conditions on grain refinement and fatigue behaviour in magnesium alloys, Mater. Sci. Eng. A, 434 (2006) 131–140. [20] Ochi, Y., Masaki, K., Hirasawa, T., Wu, X., Matsumura, T., Takigawa, Y., Higashi, K., High Cycle Fatigue Property and Micro Crack Propagation Behavior in Extruded AZ31 Magnesium Alloys, Mater. Trans., 47 (2006) 989–994. [21] Tsushida, M., Shikada, K., kitahara, H., Ando, S., Tonoda, H., Relationship between Fatigue Strength and Grain Size in AZ31 Magnesium Alloys, Mater. Trans., 49 (2008) 1157–1161. [22] Sajuri, Z.B., Miyashita, Y., Hosokai, Y., Mutoh, Y., Effects of Mn content and texture on fatigue properties of as-cast and extruded AZ61 magnesium alloys, Int. J. Mech. Sci., 48 (2006) 198–209. [23] Ishihara, S., Nan, Z., Goshima, T., Effect of Microstructure on Fatigue Behavior of AZ31 Magnesium Alloy, Mater. Sci. Eng. A, 468-470 (2007) 214–222. [24] Zeng, R.C., Xu, Y.B., Ke, W., Han, E.H., Fatigue crack propagation behavior of as-extruded magnesium alloy AZ80, Mater. Sci. Eng. A, 509 (2009) 1–7. [25] Zeng, R., Han, E., Ke, W., Dietzel, W., Kainer, K.U., Atrens, A., Influence of microstructure on tensile properties and fatigue crack growth in extruded magnesium alloy AM60, Int. J. Fatigue, 32 (2010) 411–419. [26] Yang, F., Yin, S.M., Li, S.X., Zhang, Z.F., Crack initiation mechanism of extruded AZ31 magnesium alloy in the very high cycle fatigue regime, Mater. Sci. Eng. A, 491 (2008) 131–136.