Issue34

B. Žužek et alii, Frattura ed Integrità Strutturale, 34 (2015) 160-168; DOI: 10.3221/IGF-ESIS.34.17 168 [8] Ardehali Barani, A., Li, F., Romano, P., Ponge, D., Raabe, D., Design of high-strength steels by microalloying and thermomechanical treatment, Materials Science and Engineering, A463 (2007) 138-146. [9] Zhang, C.-l., Liu, Y.-z., Jiang, C., Xiao, J.-f., Effects of Niobium and Vanadium on Hydrogen-Induced Delayed Fracture in High Strength Spring Steel, Journal of Iron and Steel Research, International, 18 (2011) 49-53. [10] Zhang, C.-l., Liu, Y.-z., Zhou, L.-y., Jiang, C., Secondary Hardening, Austenite Grain Coarsening and Surface Decarburization Phenomenon in Nb-Bearing Spring Steel, Journal of Iron and Steel Research, International, 19 (2012) 47-52. [11] Ganesh, P., Sundar, R., Kumar, H., Kaul, R., Ranganathan, K., Hedaoo, P., Tiwari, Pragya, Kukreja, L.M., Oak, S.M., Dasari, S., Raghavendra, G., Studies on laser peening of spring steel for automotive applications, Optics and Lasers in Engineering, 50 (2012) 678-686. [12] Li, W., Sakai, T., Wakita, M., Mimura, S., Effect of surface finishing and loading condition on competing failure mode of clean spring steel in very high cycle fatigue regime, Materials Science and Engineering, A552 (2012) 301-309. [13] Dziemballa, H., Manke, L., Steel, Future for the Automotive Industry, Verlag Stahleisen GmbH, Dusseldorf, (2005) 341-348. [14] Ardehali Barani, A., Ponge, D., Optimized Thermomechanical Treatment for Strong and Ductile Martensitic Steels, Materials Science Forum, 539-543 (2007) 4526-4531. [15] Assefpour-Dezfuly, M., Brownrigg, A., Parameters affecting sag resistance in spring steels, Metallurgical and Materials Transactions A, 20 (1989) 1951-1959. [16] Shin, J.-C., Lee, S., Hwa Ryu, J., Correlation of microstructure and fatigue properties of two high-strength spring steels, International Journal of Fatigue, 21 (1999) 571-579. [17] Krauss, G., McMahon, C.J., Martensite, ASM International, Materials Park, (1992). [18] Bytyqi, A., Puksic, N., Jenko, M., Godec, M., Characterization of the inclusions in spring steel using light microscopy and scanning electron microscopy, Materials and technology, 45 (2011) 55-59. [19] Wang, X.H., Jiang, M., Chen, B., Li, H.B., Study on formation of non-metallic inclusions with lower melting temperatures in extra low oxygen special steels, Science China Technological Sciences, 55 (2012) 1863-1872. [20] Senčič, B., Leskovšek, V., Fracture toughness of vacuum heat treated spring steel 51CrV4. Materials and Technology, 45 (2011) 67-73. [21] Roberts, G., Kraus, G., Kennedy, R., Tool Steels. 5th edition, ASM International, Materials Park, (1998). [22] Tang, W., Wu, X., Min, Y., Xu, L., Effect of microstructural homogeneity on mechanical and thermal fatigue behavior of a hot-work tool steel, Proceedings of 6th International Tooling Conference, Karlstad University, Sweden, (2002) 755-765. [23] Li, W., Sakai, T., Wakita, M., Mimura, S., Influence of microstructure and surface defect on very high cycle fatigue properties of clean spring steel, International Journal of Fatigue, 60 (2014) 48–56. [24] Li, W., Sakai, T., Wakita, M., Mimura, S., Effect of surface finishing and loading condition on competing failure mode of clean spring steel in very high cycle fatigue regime, Materials Science and Engineering: A, 552 (2012) 301–309. [25] Podgornik, B., Leskovšek, V., Godec, M., Senčič, B., Microstructure refinement and its effect on properties of spring steel, Materials Science and Engineering: A, 599 (2014) 81–86. [26] Podgornik, B., Žužek, B., Leskovšek, V., Experimental Evaluation of Tool Steel Fracture Toughness Using Circumferentially Notched and Precracked Tension Bar Specimen, Materials Performance and Characterization, 3 (2014) 1-17. [27] Wei, S., Tingshi, Z., Daxing, G., Dunkang, L., Poliang, L., Xiaoyun, Q., Fracture toughness measurement by cylindrical specimen with ring-shaped crack, Eng. Fract. Mech. 16 (1982) 69-82. [28] Gdoutos, E.E., Fracture Mechanics Criteria and Applications, Kluwer Academic Publishers, London, (1990).