General Papers
| A Comparison of Different Methods for Determination of Elastic-Plastic R-Curves | |
| H.-J. Kaiser |
| A Comparison of Mode III and Mode I Toughness in Quenched and Tempered Steels | |
| N. J. Hurd, P. E. Irving |
| An Elastic-Plastic Crack Growth Analysis Using the J-Integral Concept | |
| J. K. Musuva, J. C. Radon |
| Correlation between Thickness and Crack Length as a Means of Achieving Plane Strain Conditions | |
| P. M. S. T. de Castro, J. Spurrier, P. Hancock |
| Crack Edge Instability - A Criterion for Safe Crack Propagation Limit in Thin Sheets | |
| B. K. Parida |
| Crack Initiation and Growth in Stainless Steel Tubes Under Thermal Shocks | |
| J. Bernard, L. Lamain, G. Verzeletti |
| Current Aspects of Crack Growth Under Monotonic Loading | |
| D. A. Curry, J. F. Knott |
| Determining the Defect Tolerance of Structures Failing by Ductile Crack Growth | |
| G. G. Chell, I. Milne |
| Direct Observation at a Sharp Crack Tip Vicinity in Hydrogenerated Austenitic Stainless Steel | |
| Y. Katz, H. Mathias, S. Nadiv |
| Effect of Specimen Size on Fracture Toughness in the Ductile Brittle Transition Region of Steel | |
| D. Munz, H. P. Keller |
| Evaluation of Defects in Welds for Brittle and Ductile Failure Modes | |
| R. Fleissig, A. Schopper, R. Steinbuch, R. Wellein |
| Evaluation of the J-Integral by Analytical and Finite Element Methods | |
| M. H. Bleackley, A. R. Luxmoore, J. Sump |
| Experimental and Theoretical Study of Cracks in Mixed Mode Conditions | |
| P. Jodin, G. Pluvinage, G. Loubignac, D. Serres |
| Experimental Investigations of the Path Independence of the J-Integral for Large Plastic Zones | |
| Th. Muller, D. Gross, D. Gross |
| Fatigue of Ti-6Al-4V with a Widmanstatten Microstructure | |
| R. Brown |
| Fatigue Studies of a High Strength Age Hardening Wrought Cu-Ni Alloy | |
| T. V. Duggan, C. Dimbylow, R. Jones |
| Finite Element Method and its Application to Two- and Three- Dimensional Elastic-Plastic Analysis of Fracture Toughness Specimens | |
| E. Keim, W. Schmitt |
| Fracture Mechanics in the Elastic-Plastic Regime | |
| G. G. Chell |
| Fracture Toughness of Nitrogen Strengthened Austenitic Steels at 4K | |
| H. Krauth, A. Nyilas |
| Introduction to Session Nine: Thin Sheet Fracture Mechanics | |
| K.-H. Schwalbe |
| J-Integral Measurements with Ceramic Materials at High Temperatures | |
| K. Kromp, R. F. Pabst |
| Load Cycling of Cracked Plates in Tension | |
| C. M. Branco, J. Saldanha Peres |
| Methods for Predicting Residual Strength of Thin-Walled Components | |
| W. Geier, K. Heckel, M. Klehr |
| Microcracking in Cast Irons | |
| G. Zambelli |
| Micromechanisms of Fatigue Fracture | |
| B. I. Verkin, N. M. Grinberg |
| Micromechanisms of Subcritical Crack Growth of Partially- Stabilized Zirconia (PSZ) | |
| Li-shing Li, R. F. Pabst |
| R- Curves Evaluation for Centre Cracked Panels | |
| K.-H. Schwalbe, W. Setz |
| Resistance to Ductile Tearing of a Structural Steel in Three and Four Point Bending | |
| G. Green, A. A. Willoughby |
| Sizing of Spot Welds by Elastic/Plastic Analysis | |
| R. A. Smith |
| Some Experience in R-Curve Technique | |
| W. Oberparleiter, X.J. Kurth |
| Stable Growth of a Penny-Shaped Crack Subjected to Thermal Load | |
| M. P. Wnuk |
| The Crack Tip Opening Displacement of Semi-Elliptical Surface Cracks in Tensile Plates | |
| G. Prantl, M. Prodan |
| The Description of Shape Development of 2 Dimensional (Semi)-Elliptic Surface Defects Using a Maximum Compliance Increase Hypothesis for Defect Growth | |
| H. C. van Elst, J. W. Tichler |
| The Effect of Secondary Hardening on the Fracture Toughness of a Bainitic Microstructure | |
| H. Kotilainen? |
| The Effect of Triaxiality on Ductile-Cleavage Transitions in a Pressure Vessel Steel | |
| I. Milne, D. A. Curry |
| The Geometry Dependence and Significance of Maximum Load Toughness Values | |
| O. L. Towers, S. J. Garwood |
| The Influence of Fracture Mode Transition on the Compliance of Thin Section Fracture Specimens | |
| D. Rhodes, L. E. Culver, J. C. Radon |
| The Influence of Plastic Deformation on Crack Propagation in Sodium Chloride | |
| M. Breucker, R. Steinbrech |
| The Significance of Mode X Branch Cracks for Combined Mode Failure | |
| L. P. Pook |
| The Stress Intensity Factors for Griffith Crack(s) in an Orthotropic Strip in the Presence of Asymmetrical Body Forces | |
| P. S. Kushwaha |
| Three-Dimensional Elastic-Plastic Finite Element Analysis of V-Notched Bars and Biaxial Loaded Through- Cracked Panels | |
| H.-H. Erbe |
| Three-Dimensional Elasto-Plastic FEM Calculations of CT Specimens with Special View of Investigating the Influence of Specimen Thickness on Plastic Zone Size | |
| J. Redmer, W. Dahl |
| Two Dimensional Fe-calculations of Cracked X6CrNil8l1 Weldments Stretched Monotonically to Limit Load | |
| B. Ruttenauer |
| Use of the R-Curve for Design with Contained Yield | |
| C. E. Turner |
| Vacuum Effect on Fatigue Crack Propagation at Low Rate | |
| J. Petit, N. Ranganathan, J. de Fouquet |
| Fracture Mechanics in the Elastic-Plastic Regime | |
| G. G. Chell |